What repairs can fix the P0602 code? Most often, the output , or there is a bad connection in the circuit. This emulsion coating may short the electrical circuitry of the input and output speed sensor signals resulting in an erratic speedometer. It's fixable but it will cost a lot of money just in part's not including labor to repair it. What I don't understand is how can a speed sensor make the car not go into gear? The easiest way to find out what this light is telling you is to hook your vehicle up to a scan tool. I posted the trouble tree for low input sensor voltage and low output sensor voltage that way he can check the sensor's he installed. What causes the P0723 code? I put in 8 injectors, new fuel filter, resealed the filter housing and changed the oil. What are the common causes of code P0974? Scanned the code turns out to be P0700 -- Transaxle Control System Malfunction erased the code, drove it around the block with no problem.
And how could I get it to you without the whole world knowing his number? Having the code's would really help to figure out the proper repair. If you want to download it in a. First, check that there are no other stored or pending codes. I will let you know where he ordered the part and the part number, could you please look at it and see if that is both the input and output sensor, or is it the right part in the first place. An intermittent harness problem may be checked by wiggling the harness and connectors and watching resistance measurements.
Can this vehicle be fixed, or is it junk yard material? Verify that the speedometer fluctuation concern has been repaired. The code is set when the transmission computer is unable to complete an operation due to bad or missing data when no other trouble codes are present. That is where the Saturn Vue is. YourMechanic offers certified mobile mechanics who will come to your home or office to diagnose and repair your vehicle. Can it be something major? But if it has low transmission fluid pressure then it could have a bad valve body or bad transmission pump I have seen both but have seen more bad valve body's then pump's. It may be wise to disconnect these connectors and make sure there are no bent pins, corrosion, or water entry.
Need help with a P0723 code? Typical resistance should be somewhere between 10 Ω and 20 Ω. Be on the lookout for nesting materials and droppings, which may point you directly to the open circuit. Test your fuel injector for cylinder 3! Truck came in about a month ago with crankcase full of fuel. This misdiagnosis can lead to an unsuccessful repair and a return of the code. As with most repairs, the diagnostic process begins with pulling stored codes and freeze frame data using a specialized scanner. You probably changed computers for nothing! Ignition voltage is supplied directly to the fuel injectors. M 8 ft-lbs in the sequence shown.
I have a full set of 2002 saturn factory vue repair manual's which should have the same code's as the 2003 vue and there isn't a code p0715 listed. He did not see any gel. He currently does not have time to tow it back to the base car shop to get the exact code. If not, repair the open circuit in the harness. Tighten Tighten the bolt to 11 N. The customers complaint is on start up the abs light and traction control message will intermittently come on and the warning chime will sound.
After the drive cycle, the engine should be idling normally. Here are some of the most common. YourMechanic offers certified mobile mechanics who will come to your home or office to diagnose and repair your vehicle. He does not have the original codes because he has used it since on a friends vehicle. In addition to these symptoms, cars with this stored code also suffer from and a. . When he hooked it up, the new code that came up was P0720.
Because while the lights vary in appearance from vehicle to vehicle, all have the same basic meaning: There's a problem with the car's emissions system. This fault code can cause significant drivability problems, which may lead to further damage to the vehicle. Does he need to put it back on the Saturn again, or can you figure out what is going on? Depending on make and model, you may be checking for resistance between two terminals or between one terminal and body ground. Never liked them I remember the first time I saw and drove one of the vue's with that transmission when I went to saturn training for it. If everything else is determined to be functioning correctly, your mechanic may use an oscilloscope to live monitor the transmission output speed sensor data. Ben is in the U. Problem is if it has low transmission fluid pressure then the side cover could be damaged.
Ben ordered the part through Auto Zone. If it has a speed sensor code it could need speed sensor's I have replaced speed sensor's on those transmission's before. I've replaced the speed sensor and filled it up with transmission fluid. I can drive this t. It should be somewhere between 12 and 18 Ω. I don't know if this web site would let you call a cell number and you could talk to Ben.
With temperatures getting as low as windchill -30 degrees, a vehicle is a necessity and this Saturn has let him down. Remove the control valve body cover gasket. Otherwise, the diagnostic process can become time consuming and cost prohibitive for the mechanic. If you could please look this up and let me know if that was the correct part or not, I sure would appreciate it. If the harness is good, the last remaining part is the shift solenoid itself. What causes the P0602 code? Tighten Bolts to 11 N. Remove the 2 bolts and the input and output speed sensor assembly from the transaxle case assembly.
This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation. The mechanic should also make sure that all connectors are securely connected. Circuit checks should determine whether you have a break in the sub-harness or an open solenoid. When the automatic transmission was invented, it did all these things using an ingenious arrangement of spool valves, operated purely by variances in hydraulic pressure. Check that all connectors are properly connected.